Predicting Degradation Mechanisms in Lithium Bistriflimide "Water-In-Salt" Electrolytes For Aqueous Batteries.

Aqueous solutions are crucial to most domains in biology and chemistry, including in energy fields such as catalysis and batteries. Water-in-salt electrolytes (WISEs), which extend the stability of aqueous electrolytes in rechargeable batteries, are one example. While the hype for WISEs is huge, commercial WISE-based rechargeable batteries are still far from reality, and there remain several fundamental knowledge gaps such as those related to their long-term reactivity and stability. Here, we propose a comprehensive approach to accelerating the study of WISE reactivity by using radiolysis to exacerbate the degradation mechanisms of concentrated LiTFSI-based aqueous solutions. We find that the nature of the degradation species depends strongly on the molality of the electrolye, with degradation routes driven by the water or the anion at low or high molalities, respectively. The main aging products are consistent with those observed by electrochemical cycling, yet radiolysis also reveals minor degradation species, providing a unique glimpse of the long-term (un)stability of these electrolytes.

Radiolysis of Electrolytes in Batteries: A Quick and Efficient Screening Process for the Selection of Electrolyte-Additive Formulations.

Understanding aging phenomena in batteries is crucial to the design of efficient, safe, and reliable energy storage devices as a part of the current green energy transition. Among the different aspects of a battery, the behavior of the electrolyte is a key parameter. Therefore, screening the aging characteristics of different electrolytes is of major interest. However, few screening studies exist because these are time-consuming and require the monitoring of numerous charge and discharge cycles. It has been demonstrated here that radiation chemistry, i.e., the interaction between ionizing radiation and matter, is a valuable tool to screen the behavior of various electrolytes within a few hours. Indeed, the rapid radiolysis of electrolytes leads to the production of the same gases as produced by electrochemical cycling (i.e., H2 , CO2 ), and the ranking of electrolytes by their H2 production yields similar performance ratings to those reported in the literature. Therefore, this direct comparison of electrolytes alone, lasting a few hours without any manufacturing operations such as the fabrication of electrochemical cells, demonstrates that controlled irradiation makes it possible to predict battery cycling behavior. Additionally, mechanisms involved in the degradation processes of different electrolytes are proposed.

Experimental determination of the curvature-induced intra-wall polarization of inorganic nanotubes.

Inspired by a natural nano-mineral known as imogolite, aluminosilicate inorganic nanotubes are appealing systems for photocatalysis. Here, we studied two types of synthetic imogolites: one is completely hydrophilic (IMO-OH), while the other has a hydrophilic exterior and a hydrophobic interior (IMO-CH3), enabling the encapsulation of organic molecules. We combined UV-Vis diffuse reflectance spectroscopy of imogolite powders and X-ray photoelectron spectroscopy of deposited imogolite films and isolated nanotubes agglomerates to obtain not only the band structure, but also the quantitative intra-wall polarization of both synthetic imogolites for the first time. The potential difference across the imogolite wall was determined to be 0.7 V for IMO-OH and around 0.2 V for IMO-CH3. The high curvature of the nanotubes, together with the thinness of their wall, favors efficient spontaneous charge separation and electron exchange reactions on both the internal and external nanotube surfaces. In addition, the positions of their valence and conduction band edges make them interesting candidates for co-catalysts or doped catalysts for water splitting, among other possible photocatalytic reactions relevant to energy and the environment.

Radiolytic Approach for Efficient, Selective and Catalyst-free CO2 Conversion at Room Temperature.

The present study proposes a new approach for direct CO2 conversion using primary radicals from water irradiation. In order to ensure reduction of CO2 into CO2-. by all the primary radiation-induced water radicals, we use formate ions to scavenge simultaneously the parent oxidizing radicals H. and OH. producing the same transient CO2-. radicals. Conditions are optimized to obtain the highest conversion yield of CO2 . The goal is achieved under mild conditions of room temperature, neutral pH and 1 atm of CO2 pressure. All the available radicals are exploited for selectively converting CO2 into oxalate that is accompanied by H2 evolution. The mechanism presented accounts for the results and also sheds light on the data in the literature. The radiolytic approach is a mild and scalable route of direct CO2 capture at the source in industry and the products, oxalate salt and H2 , can be easily separated.

Reaction Mechanisms of the Degradation of Fluoroethylene Carbonate, an Additive of Lithium-Ion Batteries, Unraveled by Radiation Chemistry.

Numerous additives are used in the electrolytes of lithium-ion batteries, especially for the formation of an efficient solid electrolyte interphase at the surface of the electrodes. Understanding the degradation processes of these compounds is thus important; they can be seen through radiolysis. In the case of fluoroethylene carbonate (FEC), picosecond pulse radiolysis experiments evidenced the formation of FEC.- . This radical is stabilized in neat FEC, whereas the ring opens to form more stable radical anions when FEC is a solute in other solvents, as confirmed by quantum chemistry calculations. In neat FEC, pre-solvated electrons primarily undergo attachment rather than solvation. On long timescales, the gases produced (H2 , CO, and CO2 ) were quantified. A reaction scheme for both the oxidizing and reducing pathways at stake in irradiated FEC is proposed. This work shows that the nature of the primary species formed in FEC depends on the amount of FEC in the solution.

Confined water radiolysis in aluminosilicate nanotubes: the importance of charge separation effects.

Imogolite nanotubes are potentially promising co-photocatalysts because they are predicted to have curvature-induced, efficient electron-hole pair separation. This prediction has however not yet been experimentally proven. Here, we investigated the behavior upon irradiation of these inorganic nanotubes as a function of their water content to understand the fate of the generated electrons and holes. Two types of aluminosilicate nanotubes were studied: one was hydrophilic on its external and internal surfaces (IMO-OH) and the other had a hydrophobic internal cavity due to Si-CH3 bonds (IMO-CH3), with the external surface remaining hydrophilic. Picosecond pulse radiolysis experiments demonstrated that the electrons are efficiently driven outward. For imogolite samples with very few external water molecules (around 1% of the total mass), quasi-free electrons were formed. They were able to attach to a water molecule, generating a water radical anion, which ultimately led to dihydrogen. When more external water molecules were present, solvated electrons, precursors of dihydrogen, were formed. In contrast, holes moved towards the internal surface of the tubes. They mainly led to the formation of dihydrogen and of methane in irradiated IMO-CH3. The attachment of the quasi-free electron to water was a very efficient process and accounted for the high dihydrogen production at low relative humidity values. When the water content increased, electron solvation dominated over attachment to water molecules. Electron solvation led to dihydrogen production, albeit to a lesser extent than quasi-free electrons. Our experiments demonstrated the spontaneous curvature-induced charge separation in these inorganic nanotubes, making them very interesting potential co-photocatalysts.

Dynamics in hydrated inorganic nanotubes studied by neutron scattering: towards nanoreactors in water.

Water dynamics in inorganic nanotubes is studied by neutron scattering technique. Two types of aluminosilicate nanotubes are investigated: one is completely hydrophilic on the external and internal surfaces (IMO-OH) while the second possesses an internal cavity which is hydrophobic due to the replacement of Si-OH bonds by Si-CH3 ones (IMO-CH3), the external surface being still hydrophilic. The samples have internal radii equal to 7.5 and 9.8 Å, respectively. By working under well-defined relative humidity (RH) values, water dynamics in IMO-OH was revealed by quasi-elastic spectra as a function of the filling of the interior of the tubes. When one water monolayer is present on the inner surface of the tube, water molecules can jump between neighboring Si-OH sites on the circumference by 2.7 Å. A self-diffusion is then measured with a value (D = 1.4 × 10-5 cm2 s-1) around half of that in bulk water. When water molecules start filling also the interior of the tubes, a strong confinement effect is observed, with a confinement diameter (6 Å) of the same order of magnitude as the radius of the nanotube (7.5 Å). When IMO-OH is filled with water, the H-bond network is very rigid, and water molecules are immobile on the timescale of the experiment. For IMO-OH and IMO-CH3, motions of the hydroxyl groups are also evidenced. The associated relaxation time is of the order of 0.5 ps and is due to hindered rotations of these groups. In the case of IMO-CH3, quasi-elastic spectra and elastic scans are dominated by the motions of methyl groups, making the effect of the water content on the evolution of the signals negligible. It was however possible to describe torsions of methyl groups, with a corresponding rotational relaxation time of 2.6 ps. The understanding of the peculiar behavior of water inside inorganic nanotubes has implications in research areas such as nanoreactors. In particular, the locking of motions inside IMO-OH when it is filled with water prevents its use under these conditions as a nanoreactor, while the interior of the IMO-CH3 cavity is certainly a favorable place for confined chemical reactions to take place.

Influence of confinement on free radical chemistry in layered nanostructures.

The purpose of the present work was to study how chemical reactions and the electronic structure of atoms are affected by confinement at the sub-nanometer scale. To reach this goal, we studied the H atom in talc, a layered clay mineral. Talc is a highly 2D-confining material with the width of its interlayer space close to angstrom. We investigated talc with a particle accelerator-based spectroscopic method that uses elementary particles. This technique generates an exotic atom, muonium (Mu), which can be considered as an isotope of the H atom. Moreover, the technique allows us to probe a single atom (H atom) at any time and explore the effects of the layered clay on a single ion (proton) or atom. The cation/electron recombination happens in two time windows: one faster than a nanosecond and the other one at longer than microseconds. This result suggests that two types of electron transfer processes take place in these clay minerals. Calculations demonstrated that the interlayer space acts as a catalytic surface and is the primary location of cation/electron recombination in talc. Moreover, the studies of the temperature dependence of Mu decay rates, due to the formation of the surrogate of H2, is suggestive of an "H2" formation reaction that is thermally activated above 25 K, but governed by quantum diffusion below 25 K. The experimental and computational studies of the hyperfine coupling constant of Mu suggest that it is formed in the interlayer space of talc and that its electronic structure is extremely changed due to confinement. All these results imply that the chemistry could be strongly affected by confinement in the interlayer space of clays.

Observation and Simulation of Transient Anion Oligomers (LiClO4)n- (n = 1-4) in Diethyl Carbonate LiClO4 Solutions.

NMR measurements show that diethyl carbonate (DEC, a solvent with a low dielectric constant) solutions of LiClO4 contain (LiClO4)n oligomers. The reduction of these species by solvated and presolvated electrons is followed by picosecond pulse radiolysis measurements. The data analysis shows that several anions absorbing in the near-infrared (NIR) and visible range are formed after the 7 ps electron pulse. In contrast with tetrahydrofuran (THF) solutions of LiClO4, the anionic monomer (LiClO4)- is not observed in DEC solutions. This is due to the fact that DEC is a nonpolar solvent favoring the clustering of monomers in the nonirradiated solution, as shown by NMR results, and also due to the instability of the anionic monomer. The absorption spectra of the anionic dimer (LiClO4)2-, trimer (LiClO4)3-, and tetramer (LiClO4)4- are clearly observed in NIR and visible ranges. Compared to the results obtained for the same system in THF and in agreement with simulated absorption spectra, the experimental results show that the absorption bands are shifted to the blue end of the spectrum when n increases. The kinetics recorded for the molar LiClO4 solution indicates that the solute is only in the form of oligomers (LiClO4)n with a large n value and that the reduced species absorb weakly in the visible region. Lastly, and contrary to what is known for well-separated ions in polar solvents, it is shown that the (LiClO4)n- anions are not stable with respect to self-reduction, leading to the decomposition of perchlorate anions. In this reaction, the perchlorate anion ClO4- is reduced by the Li atom into a chlorate anion ClO3-. This is proved by the presence of ClO3- and chlorinated species detected by mass spectrometry measurements in irradiated DEC solutions containing LiClO4.

Degradation of an Ethylene Carbonate/Diethyl Carbonate Mixture by Using Ionizing Radiation.

The reactivity of ethylene carbonate (EC) and of a EC/diethyl carbonate (DEC) mixture was studied under ionizing radiation to mimic the aging phenomena that occur in lithium-ion batteries. Picosecond-pulse radiolysis experiments showed that the attachment of the electron to the EC molecule is ultrafast (k(e-EC +EC)=1.3×109  L mol-1 s-1 at 46 °C). This reaction rate is accelerated by a factor of 5.7 compared with the electron attachment to propylene carbonate, which implies that the presence of the methyl group significantly slows the reaction. In a 50:50 EC/DEC mixture, just after the electron pulse the electron is solvated by a mixture of EC and DEC molecules, but its fast decay is attributed exclusively to electron attachment to the EC molecule. Stable products detected after steady-state irradiation were mainly H2 , CH4 , CO, and CO2 . The evolution of the radiolytic yields with the EC fraction shows that H2 and CH4 did not exhibit linear behavior, whereas CO and CO2 did. Indeed, H2 and CH4 mainly arise from the excited state of DEC, the formation of which is significantly affected by the evolution of the dielectric constant of the mixture and by the electron attachment to EC. CO formation is mainly due to the reactivity of the EC molecule, which is not affected in the mixture, as proven by pulse-radiolysis experiments.

Ionosilicas as efficient sorbents for anionic contaminants: Radiolytic stability and ion capacity.

Ammonium based hybrid ionosilicas were prepared from tetrasilylated ammonium precursors. The formed material exhibited high specific surface area together with mesoporosity. Our results indicate that ionosilicas display high exchange capacity for iodide. They were submitted to 10MeV electron irradiation at a total dose of 1.7MGy. Irradiation was shown not to alter the properties of ionosilica: the morphological, textural and surface properties of the material are hardly modified. The sorption properties (sorption capacity and cumulative displacement enthalpy) are similar before and after electron irradiation. This high radiolytical stability confirms that these innovative materials have therefore high potential as anion traps for future applications in decontamination processes or long term storage of radioactive waste.

Picosecond Pulse Radiolysis of Propylene Carbonate as a Solute in Water and as a Solvent.

The ester propylene carbonate (PC) is a solvent with a high static dielectric constant where the charges generated by ionizing radiation are expected to be long-lived at room temperature. Time-resolved optical absorption spectroscopy after picosecond electron pulses reveals the formation of a UV band, within less than two nanoseconds, that is assigned to the radical anion PC(-•), arising from a fast attachment reaction of electrons onto PC. Assignment and reactivity of PC(-•) in neat solvent and solutions are discussed in relation with data obtained in solutions of PC in water under reducing or oxidizing conditions and in solutions in PC of aromatic scavengers with various reduction potentials. The fate of the electrons and the ionization yield in PC are compared with those of other solvents.

Identification of Transient Radical Anions (LiClO4)(n)(-) (n = 1-3) in THF Solutions: Experimental and Theoretical Investigation on Electron Localization in Oligomers.

Picosecond pulse radiolysis measurements of tetrahydrofuran (THF) solutions containing LiClO4 over a wide range of concentration are performed to investigate the formation of transient species. The (35)Cl NMR measurements of these solutions prior to irradiation show that the salt is in the form of (LiClO4)n oligomers. Kinetics and transient absorption spectra of intermediates in each solution are obtained on the time scale from 10 to 3800 ps. A global spectro-kinetic matrix of the data is analyzed by the multicurve resolution alternated least-squares (MCR-ALS) method. It shows the presence of 3 transient species induced by electron pulse, in addition to the solvated electron. A hybrid Monte Carlo/DFT molecular simulation method is elaborated, using the MPW1K functional for the configuration sampling and B3LYP for the spectra calculations. The maximum of the absorption band of the monomer (LiClO4)(-), dimer (LiClO4)2(-), trimer (LiClO4)3(-), and tetramer (LiClO4)4(-) anions are deduced from the simulations. They enable one to label the MCR-ALS spectra (differences are below 0.1 eV) and to interpret the kinetic data. The simulations show also that Li(I) ion catalyzes the reduction of perchlorate by excess electrons. Only the dimer anion, due to its unique structure with a stable Li2(+) core and two nonbridging perchlorates, presents higher stability toward ClO4(-) reduction into ClO3(-). It corresponds to the long-lived species observed in the experiments.

Ultrafast Decay of the Solvated Electron in a Neat Polar Solvent: The Unusual Case of Propylene Carbonate.

The behavior of carbonates is critical for a detailed understanding of aging phenomena in Li-ion batteries. Here we study the first reaction stages of propylene carbonate (PC), a cyclical carbonate, by picosecond pulse radiolysis. An absorption band with a maximum around 1360 nm is observed at 20 ps after the electron pulse and is shifted to 1310 nm after 50 ps. This band presents the features of a solvated electron absorption band, the solvation lasting up to 50 ps. Surprisingly, in this polar solvent, the solvated electron follows an ultrafast decay and disappears with a half time of 360 ps. This is attributed to the formation of a radical anion PC(-•). The yield of the solvated electron is low, suggesting that the radical anions are mainly directly produced from presolvated electrons. These results demonstrate that the initial electron transfers mechanisms are strongly different in linear compared with cyclical carbonates.

Electrolytes Ageing in Lithium-ion Batteries: A Mechanistic Study from Picosecond to Long Timescales.

The ageing phenomena occurring in various diethyl carbonate/LiPF6 solutions are studied using gamma and pulse radiolysis as a tool to generate similar species as the ones occurring in electrolysis of Li-ion batteries (LIBs). According to picosecond pulse radiolysis experiments, the reaction of the electron with (Li(+), PF6(-)) is ultrafast, leading to the formation of fluoride anions that can then precipitate into LiF(s). Moreover, direct radiation-matter interaction with the salt produces reactive fluorine atoms forming HF(g) and C2H5F(g). The strong Lewis acid PF5 is also formed. This species then forms various R(1)R(2)R(3) P=O molecules, where R is mainly -F, -OH, and -OC2H5. Substitution reactions take place and oligomers are slowly formed. Similar results were obtained in the ageing of an electrochemical cell filled with the same model solution. This study demonstrates that radiolysis enables a description of the reactivity in LIBs from the picosecond timescale until a few days.

Radiolysis as a solution for accelerated ageing studies of electrolytes in Lithium-ion batteries.

Diethyl carbonate and dimethyl carbonate are prototype examples of eco-friendly solvents used in lithium-ion batteries. Nevertheless, their degradation products affect both the battery performance and its safety. Therefore, it is of paramount importance to understand the reaction mechanisms involved in the ageing processes. Among those, redox processes are likely to play a critical role. Here we show that radiolysis is an ideal tool to generate the electrolytes degradation products. The major gases detected after irradiation (H2, CH4, C2H6, CO and CO2) are identified and quantified. Moreover, the chemical compounds formed in the liquid phase are characterized by different mass spectrometry techniques. Reaction mechanisms are then proposed. The detected products are consistent with those of the cycling of Li-based cells. This demonstrates that radiolysis is a versatile and very helpful tool to better understand the phenomena occurring in lithium-ion batteries.

H(2) formation by electron irradiation of SBA-15 materials and the effect of Cu(II) grafting.

Measurement of H(2) production from electron irradiation (10 MeV) on SBA-15 materials has shown that adsorbed water is attacked preferentially. Silanol groups are only attacked when they are in the majority with respect to adsorbed water, however they are much less efficient at producing H(2). The comparison between water content before and after electron irradiation and the corresponding H(2) production indicates that water desorption is the main route to adsorbed water loss for SBA-15 materials. On the other hand, surface silanol groups are more susceptible to attack, leading to H(2) production when SBA-15 samples have undergone extensive thermal treatment. Electron irradiation of SBA-15-Cu materials has shown that the presence of Cu(II) on the surface reduces and inhibits the production of H(2.) This inhibiting power affects adsorbed water bonded to grafted copper but not surface silanol groups.

Time-resolved studies of water dynamics and proton transfer at the alumina-air interface.

The present study aims to understand the dynamical properties of water and OH groups layered on an alumina surface mainly by means of femtosecond IR-pump IR-probe transient absorption spectroscopy. The experimental results obtained demonstrate the existence of several kinds of O-H vibrators on the surface of alumina membranes, distinguishing them by their behavior on the femtosecond time scale and by the anisotropy of their spectral response. In the high-frequency region (>3400 cm-1), the absorption is due to well-packed aluminol groups and to physisorbed water patches on the surface. When pumping at 3200 cm-1, physisorbed water hydrogen-bonded to AlOH2+ groups is observed. The anisotropy measurements demonstrate the existence of an efficient energy-transfer mechanism among the water molecules characterized by a time constant of 400 +/- 100 fs. The persisting anisotropy at long times, especially in the case of AlOH groups and of the structured physisorbed water layer on top of them, proves the anisotropic structuring induced by the surface. The excitation at 3000 cm-1 enables the detection of a photon-induced proton-transfer reaction. The proton back-transfer reaction time constant is 350 +/- 50 fs. From anisotropy measurements, we estimate the proton hopping time to be 900 +/- 100 fs in a locally extended water network lying on the surface.

Mechanism of C-O activation in dimethoxyethane cationic iron complexes.

The fragmentation mechanism of iron complexes bearing a bidentate ligand, dimethoxyethane (CH(3)OCH(2)CH(2)OCH(3), labeled as DXE) has been investigated by means of FT-ICR mass spectrometry (ion-molecule reactions) and infrared multiphoton dissociation spectroscopy. Two possible reaction mechanisms were envisioned for the Fe(DXE)(+) + DXE reaction, leading to the formation of the Fe(CH(2)O)(DXE)(+) ion. The two mechanisms differ in the nature of the neutral molecules formed: CH(3)OC(2)H(5) or CH(2)=CH(2) + CH(3)OH. The combination of ion-molecule reactions, thermochemistry considerations, and IRMPD spectra leads us to suggest that the mechanism involves successive elimination of the neutrals CH(2)=CH(2) and CH(3)OH, the first step of the mechanism being the insertion of the iron atom in the O-C(central) bond.